Resume Blog

<p>You might have had an experience that after using your <a rel="nofollow" onClick="javascript:pageTracker._trackPageview(‘/outgoing/article_exit_link’);" href="http://www.laptoptraveller.com/battery-sony-laptop-notebook-batteries.html" title="Sony Laptop Battery">Sony laptop battery</a> for several months, you noticed that your laptop battery does not last as long as a full charge as it used to. For example, at your first time using your new Sony laptop battery, it lasted for 3 hours on fully charged, but became only 1 hour or less after half a year.</p> <p>There are some possible factors to cause the situation above, such as <a rel="nofollow" onClick="javascript:pageTracker._trackPageview(‘/outgoing/article_exit_link’);" href="http://www.laptoptraveller.com/battery-sony-laptop-notebook-batteries.html" title="Laptop batteries/ adapters for Sony Laptops">your Sony laptop battery/ AC adapter</a> is faulty, a problem with your main power supply, the battery requires recalibration, or the battery is kept at too high temperature that makes it past its useful life. The procedure below is to help you to check out what’s wrong with your laptop or laptop battery:</p> <p>1)      Check out your power supply</p> <ol> <li>Use a known working AC mains lead and AC adaptor of the same type</li> <li>Connect the AC adaptor to a mains wall socket that you know is working instead of a RM NoteBus</li> <li>Switch the system on and check that the power icon at the bottom right of the system has a ‘mains plug’ symbol and that is says ‘On AC Power’ or ‘Charging’ when the pointer hovers over it</li> </ol><ol> </ol> <p>2)      Check your power scheme configuration</p> <p>Look at the Control Panel, Performance and Maintenance, Power Options and check that you have not set the ‘Running On Batteries’ settings to a short time (eg 15 minutes). This would cause the system to enter standby mode after being idle for 15 minutes. Similarly, if you have a ‘System hibernates’ option, check that this is not set for a short time. This may give the appearance that the battery is not lasting very long, but in fact the system is simply switching off after a set period of idleness.</p> <p>3)      Recalibrate the smart battery</p> <p>Notebook and tablet PC batteries are usually the Smart Lithium-Ion type. They usually include a small micro-controller unit which can predict how long the battery is going to last. This prediction feature is necessary as without it, it would be very difficult to know when the battery is about to run out of charge.</p> <p>If you consistently use the system for only an hour or so on the battery, and then connect it to the AC adaptor to recharge it, over the period of a few months the battery will ‘lose track’ of how much charge it really holds.</p> <p>In this case it may report to Casement Replacement Windows that it is about to run out of power, when in fact the battery has plenty of charge left. Casement Replacement Windows will try to shut down if the battery reports low power and so your system may shut down prematurely, even though there is still charge remaining in the battery.</p> <p>Battery calibration works by allowing the Smart battery micro-controller to re-calculate the length of time that a battery will last for. All you need to do is to ensure that the system goes from a fully charged state to a fully discharged state. This is done by simply ensuring the system stays on for as long as the battery will last.</p> <p>Battery calibration does not extend the battery discharge time. This feature calibrates the battery so that it shows the remaining charge accurately.</p> <p>The procedure is as the following</p> <ol> <li>Check your Sony laptop is on AC power</li> <li>Switch off your laptop</li> <li>Leave your laptop overnight (eight hours) to charge</li> <li>Switch on your laptop and check that the system is still on AC power</li> <li>In Control Panel, Performance and Maintenance, Power Options, and change the Power Scheme to Always On. Then change the ‘Running on Batteries’ settings to all say <strong>’Never’</strong> and click on ‘OK’</li

Posted Uncategorized |